Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateTrusted Garage Door Repair for Yonkers Homeowners
A garage door that won’t open leaves your whole day on hold. Whether it’s a snapped torsion spring, a frayed cable, or a door that grinds halfway up and stops, garage door repair in Yonkers typically runs $150 – $600, and most jobs are done the same day. At Marlow Garage Door Repair Yonkers, Jaylen Ross and our team have been fixing doors across Westchester since 2002. We show up when we say we will, hand you a written price before a single wrench turns, and back every repair with our 365-Day Done Right Promise. Need help now? Call (845) 407-9237 and a real person answers, 24/7.
Garage Door Sensor Repair
Garage door sensor repair fixes the photo-eye sensors mounted near the bottom of each door track, the small lenses that tell the opener whether anything is in the door’s path. When these sensors drift out of alignment, get knocked loose, or fail entirely, your door either won’t close or reverses immediately after touching the floor. In Yonkers, where salt air from the Hudson and winter road grime creep into everything, sensors collect film and corrosion faster than most homeowners expect. A typical garage door repair visit for sensor issues runs $150 – $600 depending on whether the sensor needs cleaning, realignment, or full replacement.
Misaligned Sensor Eyes
The most common sensor problem isn’t a dead sensor at all. It’s a bracket that shifted a quarter inch when someone bumped it with a broom, a bike, or a trash can. We realign the eyes, clean the lenses, and test the door through five full open/close cycles.
Replacement Wiring and Sensors
Older Yonkers homes, especially pre-war houses in Park Hill and Ludlow, often have original low-voltage wiring that degrades inside the wall or along the track. We test the circuit, identify where the fault is, and replace only what’s failed, not the whole opener.
Styles & brands we work with
Emergency Garage Door Repair
Emergency garage door repair is for doors that won’t close at all, leaving your home unsecured, or doors stuck open with a car trapped inside. A spring that snaps at 7 a.m. on a workday, a cable that frays and jams the door, or a door that crunches to a halt halfway up are all emergency situations. In Yonkers, Marlow Garage Door Repair runs emergency calls every day of the week. Jaylen Ross and our techs carry a full truck stock of springs, cables, rollers, and openers, so most emergency repairs finish in one visit. Emergency repair pricing falls in the standard $150 – $600 garage door repair range, and you’ll see the exact number in writing before we touch anything.
What Counts as an Emergency
If your door won’t close, that’s an emergency and we’ll treat it like one. An open garage is an open invitation, and a door stuck halfway is a safety hazard for kids and pets. Call (845) 407-9237 any time and a live person picks up, no recording.
Same-Day Response in Yonkers
We dispatch from within Yonkers, not a regional hub an hour away. That means most emergency calls see a tech arrive the same day, often within hours. You’ll get a live arrival window you can track through our Relay Visibility Guarantee.
Garage Door Panel Replacement
Garage door panel replacement swaps out a dented, rotted, or cracked section of your door instead of replacing the entire assembly. If you backed into the bottom panel or a storm drove a branch into the third row, a single new panel usually restores the door’s look and structural integrity. In Yonkers, panel replacement typically runs $250 – $500 per panel depending on the door material and whether it’s insulated steel, fiberglass, or wood. It’s the right call when the damage is isolated and the rest of the door operates smoothly.
When One Panel Is Enough
A dented bottom panel doesn’t mean you need a whole new door. As long as the tracks are straight, the hinges are intact, and the springs are balanced, a single panel brings your door back. We match the panel to your existing door’s brand, model, and color as closely as the manufacturer allows.
Matching Older Door Models
Older Clopay and Wayne Dalton doors from the early 2000s can be tricky to match exactly. We check the door’s model number, order the correct panel through our supplier network, and install it with fresh hinges and rollers if the originals show wear. You’ll know the exact price before we order anything.
Garage Door Maintenance
Garage door maintenance is a scheduled tune-up that catches wear before it becomes a breakdown. In Yonkers’s freeze-thaw winters, metal parts contract and expand, condensation rusts bearings, and rubber seals crack from months of salt spray. A maintenance visit at Marlow Garage Door Repair Yonkers runs $110 – $220 and covers tightening every bolt on the track, lubricating the rollers and hinges, checking spring balance, testing the auto-reverse safety system, and inspecting cables for fraying. Most homeowners schedule it once a year, ideally in early fall before the first hard cold snap.
What’s On Our Checklist
We check the balance of the door by disconnecting the opener and lifting manually. If the door drifts or drops, the springs are wearing unevenly. We also test the opener’s force settings to make sure it stops and reverses when it meets resistance.
Catching Yonkers Weather Damage
River frost in neighborhoods like Dunwoodie and Crestwood puts extra load on springs and hinges. We look for rust at the bottom brackets, corrosion around the cable drums, and cracked weatherstripping along the sides and top. Fixing these small things early prevents bigger garage door repair bills later.
Garage Door Roller Replacement
Garage door roller replacement removes worn or broken wheels that guide the door up and down the tracks. If your door sounds like a freight train and shakes as it moves, you’re hearing rollers with flat spots, busted bearings, or cracked nylon. In Yonkers, roller replacement runs $110 – $220 for a full set, depending on whether the door uses standard steel rollers or quieter nylon models. It’s a straightforward repair, but it’s not a good DIY job. The bottom roller brackets on many doors are connected to the high-tension cable system, and removing them without releasing tension properly can cause serious injury.
Steel vs. Nylon Rollers
Nylon rollers are quieter and gentler on metal tracks, which matters in attached garages where sound carries into the house. Steel rollers last longer but rattle as bearings wear. We’ll show you both options and the price difference before you decide.
Worn Roller Warning Signs
Look at the door as it moves past eye level. If the rollers wobble in the track or leave metal dust on the horizontal rails, they are shot. Replacing them now is cheaper than letting a seized roller gouge the track, which turns a $110 job into a full track realignment.
Commercial Garage Door Repair
Commercial garage door repair handles the heavier, harder-working doors on warehouses, auto shops, storage facilities, and loading docks across Yonkers. These doors open dozens of times a day, and every cycle puts stress on the springs, cables, and opener motor that a residential door never sees. At Marlow Garage Door Repair Yonkers, we service commercial doors with the same written pricing and 365-Day Done Right Promise we give homeowners. Commercial repair costs typically fall in the $150 – $600 range for common fixes, with more involved work quoted after inspection.
Minimizing Downtime
A loading dock door that’s down means a truck that’s waiting, and that costs money by the hour. We prioritize commercial calls in Yonkers and arrive with enough truck stock to fix most spring, cable, and opener failures in one trip. Jaylen Ross coordinates commercial scheduling directly.
High-Cycle Components
On doors that open 50 times a day, standard springs wear out in a year or two. We install high-cycle springs rated for 25,000 to 50,000 cycles, and recommend upgraded rollers and reinforced hinges for doors that get worked hard. You get the same upfront price guarantee whether it’s a standard spring or a heavy-duty one.
Brands We Service
Our techs at Marlow Garage Door Repair Yonkers are trained on eight major brands, and we stock OEM and factory-equivalent parts for LiftMaster openers, Chamberlain motors, Clopay doors, and Amarr panels. That means the tech who walks up your driveway already knows the specific quirks of your door’s brand. When a LiftMaster opener throws a specific fault code or a Clopay panel needs a specific hinge layout, we don’t have to Google it on your time.
We service Raynor and Wayne Dalton doors regularly across Yonkers, and our team has deep experience with Craftsman openers from the 1990s and early 2000s that are still running in older homes. Whether you have a Craftsman chain drive that’s been chirping for years or a Raynor steel commercial door that won’t lift evenly, we can help. Brand familiarity matters because it makes the diagnosis faster and the repair right the first time.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Your door sags on one side. A visibly uneven door usually means a broken spring or a failing cable on one side. Operating it like this bends tracks and burns out opener motors, turning a $180 spring replacement into a $600 garage door repair.
- The opener runs but the door won’t move. The emergency release cord may have been pulled, or the coupler between the motor and drive shaft is stripped. If the door is connected and still won’t move, the spring has likely failed and the opener is pushing dead weight.
- You hear a gunshot sound from the garage. A torsion spring snapping under tension sounds like a firecracker. If you heard it and the door won’t lift, stop pressing the opener button and call a pro. The spring that broke is under enough tension to cause serious injury, so this is not a DIY fix.
- The door reverses as soon as it touches the floor. This is either a sensor alignment issue or an opener force-setting problem. If the door reverses because a sensor is dirty, that’s a quick fix. If it reverses because the opener logic board is failing, you’ll want a tech to test it before you buy a new opener.
- The cable looks frayed or is hanging loose. Cables under tension can snap and whip, and a cable that slips off the drum can send the door crashing down. If you see loose cable, don’t operate the door. We’ll release the spring tension safely and replace the cable, typically for $130 – $250.
Our Process, Step by Step
- 1
You call or book online. Call (845) 407-9237 and a real person picks up, any hour, any day. Tell us what the door is doing, what brand it is, and when it started. We’ll give you a straight answer about likely causes and schedule a tech with a live arrival window you can track.
- 2
We arrive and diagnose. Jaylen Ross or one of our background-checked, uniformed techs shows up in a marked Marlow van with the truck stocked for common Yonkers door failures. We inspect the springs, cables, rollers, tracks, opener, and safety sensors, and we explain what we found in plain language.
- 3
You approve a written price. Before any work starts, you get a written quote with the exact dollar amount, the specific parts we’ll use, and how long it’ll take. The number you approve is the number on the invoice, every time. No surprises, no “while we’re here” upsells.
- 4
We complete the repair and test everything. Most garage door repairs in Yonkers finish in one visit. After the fix, we cycle the door through multiple open/close tests, verify the auto-reverse safety function, and balance the door so it opens and closes smoothly by hand.
- 5
You get a digital invoice and our 365-Day Done Right Promise. Pay from a texted link, no paper needed. Every repair carries a full year of coverage in writing. If anything fails on a part we touched, we come back and make it right at no charge.
How Much Does Garage Door Repair Cost in Yonkers?
A typical garage door repair in Yonkers runs $150 – $600, with most common jobs landing in the $180 – $340 range. Spring replacement runs $180 – $340 depending on whether you have a single torsion spring or a dual-spring setup. Cable repair runs $130 – $250. Opener repair lands between $120 and $320, while a full opener installation runs $250 – $550. Panel replacement is $250 – $500 per panel, track realignment is $120 – $240, roller replacement is $110 – $220, and a brand-new door runs $700 – $2,200 depending on size, insulation, and material. What affects the price is mostly three things: the type of spring system (torsion springs above the door cost more than extension springs on the sides), the door’s weight and width, and whether any secondary damage has occurred from running the door with a broken spring.
To avoid overpaying, get a written price before any work begins. Some companies quote low over the phone and pad the invoice after they arrive. Our written quote locks the number. Also ask whether the price includes parts and labor in one line item, and whether the warranty is in writing. Our free estimate includes the full diagnosis, a written quote, and a structural safety check of your door and opener. You don’t pay a cent to find out what’s wrong.
Our Service Area Near Yonkers
Marlow Garage Door Repair Yonkers covers Garage Door Repair in Yonkers and all surrounding Westchester and Bronx neighborhoods. We regularly run calls to New Rochelle, Scarsdale, Mount Vernon, Eastchester, and Mamaroneck, with typical response times under two hours on most Yonkers dispatches. We also serve Riverdale, Kingsbridge, Morris Park, and Throgs Neck in the Bronx. If you’re on Garage Door Repair in City Island, we cross the bridge daily. And for doors closer to Manhattan, see our page on Garage Door Repair in Morningside Heights. Not sure if we cover your street? Home base is Yonkers, and we’ve likely been there this week.
Serving Yonkers, NY - Our Local Coverage Area
We’re based in the Yonkers area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Repair in Yonkers
Garage door repair is the process of diagnosing and fixing mechanical or electrical problems that prevent your door from opening, closing, or operating safely. It includes spring replacement, cable repair, roller replacement, track realignment, opener repair, and sensor issues. In Yonkers, most residential repairs cost $150 – $600 and are completed in a single visit.
Most common repairs, including spring replacement, cable repair, and roller replacement, take 45 to 90 minutes once the tech arrives. Opener replacement or panel replacement may take two to three hours depending on the door configuration. We’ll give you a time estimate in writing before the work starts. Call (845) 407-9237 for an exact time estimate for your specific door.
Most garage door repairs in Yonkers cost between $150 and $600, with spring replacement at $180 – $340 and cable repair at $130 – $250. The exact price depends on spring type, door weight, and whether secondary damage has occurred. You’ll receive a written price before we begin any work, and that number never changes. Call (845) 407-9237 for a free estimate.
Yes. We’re factory-trained on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. Our techs carry opener parts for LiftMaster and Chamberlain on the truck, so most opener repairs finish in one visit. We diagnose the opener’s specific fault code and replace only what’s failed rather than selling you a new unit you don’t need.
In most cases, yes. We dispatch from Yonkers, not a regional office an hour away. Call (845) 407-9237 and we’ll give you a live arrival window you can track. Emergency calls run every day of the week, with many Yonkers residents seeing a tech the same day, often within a few hours. A real person answers, day or night.
Every repair carries our 365-Day Done Right Promise in writing. If a repair fails within one year, we return and fix it at no charge. No fine print, no prorating. If we touched the part and it wasn’t right, we make it right.
Clear the area around the garage door, both inside and outside, so we can access the tracks and opener. If possible, disconnect the opener and keep the door closed. Don’t try to force the door open or closed if it’s stuck. And have your opener’s brand name or the door’s model number handy if you know it.
Schedule Your Garage Door Repair Service in Yonkers Today
A garage door that doesn’t work right isn’t something to sleep on. Call (845) 407-9237 and get a free, no-obligation estimate from Jaylen Ross and the team at Marlow Garage Door Repair Yonkers. We’ll diagnose the issue, hand you a written price before any work begins, and back our repair with a 365-day guarantee in writing. Open 24/7, real person every time.
Written by Jaylen Ross, Owner at Marlow Garage Door Repair Yonkers, serving Yonkers since 2002.